This article show the guide on how to configure and verification with ISTA+.And following information is freely available on the internetThe following information is freely available on the internet, however, has been consolidated here to help the DIYer in interface configuration (Rheingold, ISTA-D and ISTA+ all are all simultaneous and are used interchangeably).

1. Berlin Diagnostics Interface (com9) Driver Windows 7
2. Berlin Diagnostics Interface (com9) Driver Download

For BMW ISTA-D/ISTA-P interface,here recommend you to use: BMW ICOM Next A + B + C (WITHOUT SOFTWARE) VXDIAG VCX SE for BMW Diagnostic and Programming Tool (WITH SOFTWARE) Part 1: BMW ista-p ista d download. Part 2: ista p ista d install (Windows 7/8.1/10) Part 3: BMW icom cable for ista. In detail Part 1: BMW ista-d ista-p download Free.

It is a WHQL-signed driver and can be used on most all versions of Windows, including Windows 8 and Windows 10. LG Mobile Driver 4.5.0 on 32-bit and 64-bit PCs This download is licensed as freeware for the Windows (32-bit and 64-bit) operating system on a laptop or desktop PC from drivers without restrictions. PC Pitstop began in 1999 with an emphasis on computer diagnostics and maintenance. During the early days of the dot com boom, our online PC maintenance tools were skyrocketing. Using Microsoft’s Internet Explorer along with ActiveX technology, we could provide free diagnostic and maintenance tools that didn’t need to be installed. Master Mst-9001d Diesel Engine Ecu Test Bench Phs For Mst-9000+ Sensor Signals Fuel Injector Condition Obd Diagnostic Interface, Find Complete Details about Master Mst-9001d Diesel Engine Ecu Test Bench Phs For Mst-9000+ Sensor Signals Fuel Injector Condition Obd Diagnostic Interface,Master Mst-9001d Diesel Engine,Ecu Test Bench Phs Master Mst-9001d,Mst-9000+ from Diagnostic Tools Supplier.

And here are other two guide on interface configure on BMW ISTA+.

BMW ENET Configuration and Verification With BMW ISTA

BMW ICOM Configuration and Verification With BMW ISTA

BMW ISTA Download & Installation & Usermanual

How To Install BMW Rheingold ISTA Software

BMW Rheingold ISTA 4.07.22/4.03.21 Free download Win7/Win8/Win10

BMW Rheigold ISTA Usermanual Download

Procedures of Configuration K+DCAN with BMW ISTA:

1. Plug your K+D-CAN cable and install drivers. For FTDI based cables use latest drivers.

2. Open “Device Manager”, then USB Serial Port properties, go to “Port Settings” tab and click “Advanced…”. Change port number to “COM9” and latency timer to “1”. Confirm configuration via “OK” button.

3.Open C:EDIABASBINEDIABAS.INI with Notepad and check for “Interface = STD:OBD”. In TCP settings set “Port = 6801”.

4.Open C:EDIABASBINOBD.INI with Notepad and check for “Port=Com9”.

5.Connect car with K+D-CAN cable to PC.

6.Now run BMW Rheingold ISTA using shortcut in start menu and wait until it boots, then press settings button.

7.Select “VCI Config” tab and “Ediabas standard settings (ediabas.ini)”, then “OK”.

8.Go “Operations”, then “Read Out Vehicle Data” and “Complete Identification”.

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

Berlin Diagnostics Interface (com9) Driver Windows 7

This Post: K+DCAN Configuration and Verification With BMW ISTA From ChinaOBD2 Official Blog
Please keep this link if you copy the post!

The instruction below introduces a creative thinking on directly load BMW ICOM Rheingold ISTA-D ISTA-P diagnostic & programming software on cheap INPA K+D CAN cable (FTDI based cable with FT232RL chip) instead of WIFI BMW ICOM A2+B+C emulators.

Tool needed:
BMW INPA K+ DCAN cable (Cheap $17.99)
Or 20-pin to 16-pin cable for BMW with 20 pin connector
BMW ICOM Rheingold ISTA-D ISTA-P software HDD
NOTE: The BMW INPA cable comes with software CD can only do diagnostic function, but if loaded with Rheingold software, it will do programming function as well. For BMW ICOM software, we recommend 2015.1V Rheingold ISTA-D 3.47 ISTA-P 54.3 software HDD which performs more stable.

Configuring Rheingold ISTA on K+DCAN cable:

1. Plug the INPA cable and install drivers. For FTDI based cables use latest drivers.
You can download driver here: www.ftdi.com

2. Set COM port. Open “My Computer”>> “Manager” >> “Device Manager” >> “Ports” >> “USB Serial Port (COM3)” >> click on “Port Setting” tab and click “Advanced”
Change the com port number to COM9 and latency time to “1”. Confirm configuration with OK button.

3. Open C://EDIABAS/BIN/EDIABAS.INI with Notepad and check for “Interface=STD:OBD”
Set “Port=6801” in TCP settings.
4. Open C://EDIABAS/BIN/EDIABAS.INI with Notepad and check for “Port=Com9”
5. Connect the INPA K+D CAN cable with PC and the other end with car via OBD socket
6. Now run BMW ICOM Rheingold software shortcut in start menu, wait until it boots, then press “Settings” button on the top
7. Select “VCI Config” tab and tick “Ediabas standard settings (ediabas.ini)”, then press “OK”
8. Go “Operations” program, then “Read Out Vehicle Data” and “Complete Identification”
9. Configuration is done. Start using the Rheingold software.

Berlin Diagnostics Interface (com9) Driver Download